manuale Jobo CPE 2

Discussioni sui vari accessori necessari in camera oscura (tank, termometri, marginatori, taglierine, focometri, timer, esposimetri, etc..)

Moderatore: etrusco

Avatar utente
teofilatto
guru
Messaggi: 972
Iscritto il: 30/04/2019, 13:48
Reputation:

manuale Jobo CPE 2

Messaggio da teofilatto »

Salve a tutti.
Sebbene immagino che il funzionamento della Jobo CPE2 sia abbastanza intuitivo, chiedo se qualcuno abbia una copia in PDF da condividere. Vorrei essere sicuro di evitare manovre dannose, tipo accendere l'apparecchio senza acqua e così via.
Grazie


- Cedete lo passo!
- Cedete lo passo, tu!

Telegram Vieni a scoprire il canale telegram di analogica.it - tantissime offerte su materiale fotografico analogico nuovo ed usato Offerte materiale analogico


Avatar utente
Maurizio Maurizio
guru
Messaggi: 351
Iscritto il: 24/11/2020, 12:40
Reputation:
Località: Roma

Re: manuale Jobo CPE 2

Messaggio da Maurizio Maurizio »

ciao Teofilatto

ti riferisci a questo?
Instructions for the JOBO CPE-2 Plus Processor.pdf
(406.95 KiB) Scaricato 279 volte
"tanto va la gatta al largo che ritorna col pattino"

Avatar utente
teofilatto
guru
Messaggi: 972
Iscritto il: 30/04/2019, 13:48
Reputation:

Re: manuale Jobo CPE 2

Messaggio da teofilatto »

Ciao @Maurizio Maurizio , ti ringrazio, ma non è questo. io ho la CPE 2 liscia, non plus. Magari per quello che mi interessa (diciamo per 'nozioni di sicurezza') sono simili?
- Cedete lo passo!
- Cedete lo passo, tu!

Avatar utente
Maurizio Maurizio
guru
Messaggi: 351
Iscritto il: 24/11/2020, 12:40
Reputation:
Località: Roma

Re: manuale Jobo CPE 2

Messaggio da Maurizio Maurizio »

a pagina 51 del pdf sono elencate le differenze nella costruzione tra le due macchine.
nell'uso però si equivalgono ;)

CPE-2 Plus Improvements

You may be wondering what the differences are between the original CPE-2, and the CPE-2 Plus Processors. Briefly, they are:

 A thermal overload was been added. This device gives additional
protection from overheating when there is not enough water in the
tempering bath. If the processor overheats, a circuit breaker trips.
Pressing the white button will reset the circuit breaker. If the thermal
overload is tripped, the processor will not heat.
 The original rotation motor was replaced with a more robust motor. This
increases the reliability of the unit with heavy loads.
 A more secure mount was made for the magnet or cog, on the end of the
motor shaft.
 The original mechanical device used for switching the rotation direction of
the motor was replaced with an electronic switching circuit. There are no
mechanical parts to wear out, or get out of alignment.
 The two speeds for rotation have been replaced with a single speed,
electronically metered at 75 rpm. The original speed of `2' was also about
75 rpm. Deleting the slower speed of `1' was done because all modern
processes worked better at the faster speed.
 The motor housing, transformer, and the entire circuit board were replaced
to accommodate the above changes.
 The JOBO product numbers were changed for the processor and the
Starter Kit.
Note: Because of these extensive changes, it is not possible to upgrade a CPE-2 to a CPE-2 Plus.
"tanto va la gatta al largo che ritorna col pattino"

Avatar utente
teofilatto
guru
Messaggi: 972
Iscritto il: 30/04/2019, 13:48
Reputation:

Re: manuale Jobo CPE 2

Messaggio da teofilatto »

Eccellente, grazie. Allora direi che va più che bene questo.
- Cedete lo passo!
- Cedete lo passo, tu!

Avatar utente
teofilatto
guru
Messaggi: 972
Iscritto il: 30/04/2019, 13:48
Reputation:

Re: manuale Jobo CPE 2

Messaggio da teofilatto »

E poco più sotto c'é questo:

Using This Manual for the Original CPE-2 Processor
You may use this instruction book for the original CPE-2 Processor, with the following changes and recommendations:
 When turning on the rotation motor, use the setting of `2'.
 The magnet and the drive cog have been changed. Use part number
#95001 for the magnet, and #95523 for the drive cog on the original
processor.
 Make sure that the three fingered reversal mechanism (it looks like a 2"
white `chicken foot'), located next to the rotation motor shaft, is pointed
towards the motor shaft. This allows the reversal switch to function.
 Be sure to fill the tempering bath with water whenever you are using the
processor. This will prevent overheating.
 Do not exceed the maximum quantity (600 ml) of chemicals or water (in a
tank or drum), for any process.
 Do not use the stainless steel reel system, as its additional weight puts too
much strain on the rotation motor.
- Cedete lo passo!
- Cedete lo passo, tu!

Telegram Vieni a scoprire il canale telegram di analogica.it - tantissime offerte su materiale fotografico analogico nuovo ed usato Offerte materiale analogico


Rispondi